Skip to main content
Back to the Journal

Opal Cutting Tools for Beginners: What You Actually Need

The opal cutting tools a beginner really needs, from safety gear and dop sticks to sanding and polish, and which extras can wait until later.

Opal Cutting · By Stephanie Caruana ·

Andamooka Opal Parcel 6 cts

To start cutting opal you need a way to grind and sand it wet, a polish, dop sticks and wax to hold the stone, a good light, and safety gear for your lungs and eyes. A cabbing machine makes the job faster, but beginners can start by hand with wet-and-dry sandpaper and patience.

What tools do you need to cut opal?

A basic opal cutting kit covers five jobs: holding the stone, removing material, smoothing it, polishing it and seeing what you're doing. Here's the list I'd give anyone starting out.

  1. Safety gear: a mask rated for fine dust, eye protection, and water to keep everything wet.
  2. Dop sticks and dopping wax: short sticks the opal is fixed to, so your fingers stay well away from the wheel.
  3. A gentle heat source for the wax: a small warmer or spirit lamp.
  4. Something to grind with: diamond wheels on a cabbing machine, or coarse wet-and-dry paper on a flat, hard backing.
  5. Sanding in finer grits: wheels, discs or wet-and-dry paper.
  6. Polish: a polishing compound such as cerium oxide on a felt, leather or canvas pad.
  7. Light and magnification: a bright torch or lamp and a 10x loupe.
  8. A marker: an aluminium or silver pencil to draw your outline on the rough.

Why is safety gear the first tool?

Opal is silica, and dry grinding makes fine silica dust that can cause serious lung disease. Cutting wet keeps the dust down, and a properly rated mask adds a second layer of protection.

  • Keep the stone and wheel wet the whole time you're grinding and sanding.
  • Wear eye protection, because small chips can fly.
  • Tie back hair and loose sleeves near anything that spins.
  • Clean up slurry while it's wet instead of sweeping up dry dust.

Do you need a machine to cut opal?

No. You can cut your first opals by hand, and plenty of cutters learn that way. A machine does the same job faster and more evenly.

Cutting by hand

Hand cutting uses wet-and-dry sandpaper in a few grits, laid flat with water. You hold the dopped stone and work it across the paper, moving from coarse to fine. It's slow, quiet and cheap, and it teaches you control. My beginner's guide to opal cutting walks through it.

Cabbing machines

A cabbing machine has a row of wheels in increasing fineness, a water feed and a polishing pad at the end. It's the standard setup for cutting cabochons. Some people build their own, and I wrote up my DIY opal cutting machine for anyone handy with tools.

Flat laps and trim saws

A flat lap is a spinning horizontal disc, useful for flattening backs and for doublet work. A trim saw with a thin diamond blade slices larger rough. Most beginners can leave both until later, because small rough can be ground to shape without them.

Which grits do you need?

Work from coarse to fine and don't skip steps. Each grit's job is to remove the scratches left by the one before it.

  • Coarse: shapes the stone and removes potch and sand. Go lightly, because it takes opal off fast.
  • Medium: refines the dome and the outline.
  • Fine: clears the medium scratches and leaves a smooth, satin surface.
  • Pre-polish: very fine grit, so the polish has nothing left to fight.

Then comes the polish. If scratches show up after polishing, the honest fix is to go back a grit or two rather than polish harder. Opal is only about 5.5 to 6.5 on the Mohs scale, so it's easy to overdo the coarse stages and lose colour you can't get back. My cabbing 101 post covers the shaping in more detail.

How do you dop an opal?

Dopping fixes the opal to a stick so you can hold and turn it safely. Here's the basic method.

  1. Grind a flat back on the rough so it sits evenly.
  2. Warm the wax until it's soft and warm the stone gently. Opal doesn't like sudden temperature changes, so never push a cold stone into hot wax.
  3. Press the stone onto the wax, centred on the stick, with the colour facing up.
  4. Let it cool slowly at room temperature before you start.
  5. When you're finished, release the stone by softening the wax again, never by levering it off.

Which tools can a beginner skip at first?

Most of the expensive extras can wait until you know you love cutting. Start small and add tools as you need them.

  • Trim saw: only needed once you're slicing larger rough.
  • Several polishing compounds: one good compound is enough to learn on.
  • Doublet gear: backing material, epoxy and a flat lap can wait until you've cut a few solid stones.
  • Expensive rough: practise on potch and inexpensive parcels first.

As I said on Instagram back in June, practise makes improvement. Your first stones won't be your best, and that's fine. Use cheap material until the shape and polish come out right, then move on to rough opal with real colour.

Questions people ask

What is the minimum equipment to cut opal?

Dop sticks and wax, wet-and-dry sandpaper in several grits, a polish and pad, water, a good light, a dust mask and eye protection. That's enough to cut and polish a small cabochon by hand.

Can you cut opal with a rotary tool?

A rotary tool can help with small shaping or carving jobs, but it's hard to get an even dome with one. Most cutters use flat paper or wheels for the main shaping and polishing.

Why do you cut opal wet?

Water keeps silica dust out of the air, stops the stone overheating and carries away grit. Heat from dry grinding can crack opal.

What should I practise on?

Potch and low-grade rough. It cuts just like precious opal, so you learn the feel of the wheel without risking good colour.