How to Dop an Opal: Wax, Glue and Getting It Level
Dopping means fixing an opal to a small stick so you can hold it steady on the wheel. Here is how to do it with dop wax or glue, how to keep the stone level, and how to get it off again safely.
Opal Cutting · By Stephanie Caruana ·

To dop an opal, you fix the flat back of the stone to the end of a small stick, called a dop, with warm dop wax or glue. The dop gives you a handle, keeps your fingers off the wheel and lets you shape the face evenly. The key is a flat back, gentle heat and a level, centred stone.
What does dopping an opal mean?
Dopping is attaching a stone to a handle so you can cut and polish it with control. The handle is the dop stick, and the stone stays on it until the face is finished.
You can shape larger pieces of opal in your fingers, and I often rough out the outline that way. Once the stone gets small, or you move on to shaping the dome, a dop makes a big difference. You can turn the stone smoothly against the wheel, see what you're doing, and keep your fingertips well away from the diamond.
What do you need to dop an opal?
You need a dop stick, something to stick the stone on with, and a gentle heat source if you're using wax. Most of it is cheap and easy to find.
- Dop sticks. Wooden dowels or flat-headed nails both work. Pick one slightly smaller than the finished stone, so the wheel never touches the dop.
- Dop wax. A firm wax made for lapidary work that softens with heat and sets hard as it cools.
- A heat source. An alcohol lamp or a small wax pot. Avoid a naked flame near the stone itself.
- Or glue. Superglue (cyanoacrylate) is a common alternative to wax, especially for small stones.
- A fine marker to draw your outline.
- Methylated spirits or acetone for cleaning up afterwards, and a freezer for releasing the stone.
How do you dop an opal with wax?
Prepare the back of the stone, warm the stone and the wax, then press the stone onto the dop and centre it before the wax sets. Take it slowly; opal does not like sudden changes in temperature.
- Grind a flat back. The back of the stone, usually the potch side, needs to be flat and clean so it sits squarely on the dop. Remove any sand or host rock from it first.
- Mark your shape. Draw the outline on the face, freehand or with a stencil, so you can see where the stone needs to sit.
- Warm the stone gently. Leave it somewhere warm, such as near (not in) the lamp, until it is warm to the touch. Wax won't grip a cold stone, and a sudden jump in temperature can crack opal.
- Heat the wax. Warm the end of the dop and build up a small cone of softened wax on it.
- Press the stone on. Push the dop onto the centre of the back of the stone and mould the wax up around the edge of the base so it supports the stone.
- Centre and level it. While the wax is still soft, check from the side and from above. Nudge the stone until it sits square on the stick.
- Let it cool naturally. Leave it at room temperature until the wax is hard. Don't put it in water or the freezer to speed this up.
Can you dop an opal with superglue?
Yes. Superglue is a quick, cold way to dop, and plenty of cutters use it, especially for small stones and calibrated work. Because there's no heat involved, it avoids the risk of warming the stone too fast.
Put a small drop of glue on a clean, flat dop, press the flat back of the stone on, and hold it level until it grabs. A gel glue gives you a few more seconds to line things up than a thin one. Give it time to cure fully before you start on the wheel, or it can let go mid-cut.
The trade-off is that glue is harder to adjust. With wax, you can soften it and nudge the stone; with glue, a crooked stone usually has to come off and go back on.
How do you keep the opal level and centred?
Level means the face of the stone sits at right angles to the dop stick. Centred means the stick sits under the middle of the stone. If either is off, every cut you make will be off too.
When I wrote about cabbing, I said: when applying the opal to the dop stick, ensure that it is level. If the opal is on a slant to begin with, then all your hard work is going to be slightly off. That's still the most important rule.
A few habits that help:
- Check from two sides. Look across the stone from the side, then turn the stick a quarter turn and look again.
- Use your outline. The dop should sit under the centre of the shape you drew, not the centre of the rough.
- Keep the stick on the hard wheels too. Using a dop even on the coarse wheels stops you pressing the stone too far into the wheel.
- Re-check as you go. If the wax softens from heat on the wheel, the stone can creep. Keep everything wet and cool.
For more on the wheels themselves, see Cabbing 101, and if you're still cutting by hand, my beginner's guide to opal cutting covers the sandpaper method.
How do you get an opal off the dop stick?
Cool it down. A few minutes in the freezer makes dop wax and superglue go brittle and shrink at a different rate to the stone, and the opal usually pops off with a gentle twist.
- Wax. Chill it briefly, then twist the stone off. Clean any leftover wax from the back with methylated spirits.
- Superglue. Chill it the same way, or soak a solid opal in acetone until the glue softens.
- Never force it. Prising a stone off with a blade is a good way to chip the edge you just finished.
- Be gentle with doublets. Doublets and triplets are glued layers and shouldn't be soaked in solvents or liquid at all.
Once the face is done, some cutters move the stone onto a second dop, stuck to the finished face, so they can tidy up the back and the setting edge. The same rules apply: flat, level, and no sudden heat.
Questions people ask
What is the best dop wax for opal?
Any proper lapidary dop wax works well. Choose one that softens at a moderate temperature, so you don't have to heat the opal much to get a good grip.
Can heat from dopping crack an opal?
It can, if the stone is heated too quickly or too much. Warm the opal gently until it's warm to the touch, never put it straight into a flame, and let it cool slowly.
What size dop stick should I use?
Use a dop slightly smaller than the finished stone. Too big and the wheel hits the stick; too small and the stone isn't well supported.
Do I need to dop opal for my first cuts?
Not always. Many beginners shape larger pieces in their fingers first, then dop once the stone is small or they start on the dome. If you'd like hands-on help, have a look at our opal cutting courses.





